~~H2O Armor

Multi-Purpose Liquid Repellant


H2O Armor is a single-step sealant, protectant, and liquid repelling spray that goes on clear, but dries to a light haze that, if desired, can be buffed to a high clear shine on most hard surfaces. Non-toxic when dry.

• Quick-drying

• One-step application

• Resists harmful UV rays

• Non-peeling/flaking formula

• One aerosol can will cover approximately 15 sq. ft.

• Also available in 1 and 5 gallon containers for larger or industrial applications.


FOR USE ON: Metal, wood, aluminum, galvanized metal, concrete, masonry, stone, paper, cardboard, fiberglass, most plastics, leathers, fabrics, canvas, and much more. Test in an inconspicuous area before treating the entire surface. Not intended to be applied to electronic devices.


PAINTING CONDITIONS: Use outdoors or in a well-ventilated area. Use when temperature is above 50°F and humidity is below 85% to ensure proper drying. Avoid spraying in windy, dusty, or wet conditions.


SURFACE PREP: Remove dirt and debris from area, and only apply on dry surfaces. Cover and mask vegetation and areas to avoid overspray.


COATING APPLICATION FOR AEROSOL:

1. Shake can vigorously for one minute after mixing ball begins to rattle (repeat often during use). If mixing ball fails to rattle DO NOT STRIKE CAN, contact Advanced Armor.

2. Spray approximately 6-12 inches from the surface. A test spray on cardboard is recommended to get a feel for the spray pattern.

3. Some applications may require more than one coat to achieve desired protection. Multiple thin coats are better than one thick coat. Allow surface to dry completely before adding a second coat.

4. Test spray in a small inconspicuous area before spraying the entire surface, some surfaces may become darker/lighter.

5. H2O Armor should be reapplied when water no longer beads up or rolls off of the surface.


HUNTING APPLICATIONS: Items that require no scent should be sprayed a few days prior to hunting to allow them to air out so the scent has time to dissipate. Shotguns and rifles should also be sprayed at least one hour prior to use to ensure that all vapors have had time to dissipate. For use on exterior of firearms only. Keep off of action and moving parts. H2O Armor is meant as a topical treatment only to help resist rust and water damage.


AEROSOL CLOGGING: After each use, turn can upside down and press spray nozzle until only clear gas comes out. If valve clogs, wear eye protection, twist and pull off spray tip, and rinse it in a solvent such as mineral spirits. Do not stick a pin or other objects into the spray button opening.


CLEAN UP: Wipe off button opening before storing. Clean up wet or dry coating with mineral spirits. Dispose of can in trash pick-up. Do not burn or place in home trash compactor. Avoid exposing treated surfaces to detergents, soaps, oils, solvents, or high-pressure water. Use only low-pressure water to clean treated surfaces. Also avoid scrubbing with brushes or abrasive cleaners.


COATING APPLICATION FOR INDUSTRIAL 1 AND 5 GALLON:


APPROXIMATE GALLON COVERAGE:

Flagstone - 125-175 sq. ft/gal.

Travertine - 200-300 sq.ft/gal.

Plain Concrete - 100-200 sq. ft./gal.

Painted Concrete - 325-425 sq. ft./gal.

Painted Wood - 325-425 sq. ft./gal.

Brick - 300-400 sq. ft./gal.

Metal - 750-850 sq. ft./gal.

Stucco - 250-325 sq. ft./gal.

Painted Stucco - 325-425 sq. ft./gal.

Vinyl - 500-600 sq. ft/gal.



MAINTAINANCE: Keep containers out of sunlight. - Store containers in an upright manner to prevent leakage. - Move all objects that could come in contact with overspray. - Containers must not be washed out or used for other purposes. - Dispose of all empty containers according to all federal, state, and local regulations


WARNING: FLAMMABLE: Keep away from heat, sparks, and open flames. HARMFUL OR FATAL IF SWALLOWED. Do not ingest. HARMFUL VAPORS. Avoid prolonged exposure to vapors. Use only in a well- ventilated area. For spray application, use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is well-ventilated. A NIOSH-approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer’s instructions for use. MAY CAUSE EYE, SKIN AND RESPIRATORY IRRITATION. Avoid contact with eyes and skin. Wear solvent-resistant gloves such as nitrile gloves. KEEP OUT OF THE REACH OF CHILDREN. Do not store above 100°F/38°C. Do not mix with other chemicals. FIRST AID PROCEDURES Eye Contact: Wash eyes with a warm, mild soap and water solution until irritation subsides. If irritation persists, call a physician. Skin: Wash with soap and warm water. Inhalation: If overcome by vapor, remove from exposure and call a physician immediately. If breathing is irregular or has stopped, start resuscitation. Administer oxygen if available. Ingestion: If ingested, DO NOT induce vomiting, call a physician immediately. *Consult MSDS prior to use*


LIMITATIONS OF LIABILITY No guarantee of accuracy is given or implied. We guarantee our products to conform to Advanced Armor quality control. We assume no responsibility for coverage, performance, or injuries resulting from its use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY ADVANCED ARMOR, EXPRESSED OR IMPLIED, STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE.


TRY H2O ARMOR...

in the industrial size, if you have a big job that needs big time protection, H2O Armor delivers lasting performance!

H2O ARMOR AEROSOL

Limitless applications... if you have something you are looking to protect from the elements, look no further than H2O Armor Aerosol.

Copyright © Advanced Armor